1 775 356 5595
1575 Linda Way, Suite 107 Sparks, NV 89431
WS-4345 5 Bay RAID DAS Wallmount Case
WS-43455 Bay RAID DAS Wallmount Case
  • Up to 5x 3.5" HDDs on removable trays w/ Hot Swap support
  • Based on Addonics 5-Port HPM-XU Port Multiplier
  • Supports RAID 0/1/3/5/10, Clone Mode (N-Type) and JBOD
  • 120mm PWM fan with top-out air flow
  • Removable 30 PPI Air Filter (clean with water, vacuum, or compressed air)
  • Rugged all steel chassis with powder coat finished door
  • 3x 1/2 inch conduit holes for secure top side wire entry / exit
  • Includes 150W FlexATX power supply
  • Support Windows, Linux and Mac OSX

Key Features

RAID 0/1/3/5/10, Clone Mode (N-Type) and JBOD

Based on Addonics 5-Port HPM-XU Port Multiplier with advanced software features

The WS-4345 DAS is built around the Addonics HPM-XU 5 Port SATA Port Multiplier/RAID Controller. This controller features the ability to configure up to to five hard drives as individual drives (JBOD) a single RAID volume (0/1/3/5/10) or operate as a disk cloning device in Clone Mode (N-Type). Modes are configured via dip switches or via included software utility.

Information and downloads regarding the Addonics 5-Port HPM-XU controller can be found at Addonics.com.

Removable, Washable, Reusable Air Filter

Cleaned with water, vacuum or compressed air

The WS-4345 uses a 30 PPI reticulated polyurethane foam filter mounted in a bottom of chassis drop-down tray. The filter in the tray and cleaning with compressed air or a vacuum cleaner allows quick pass maintenance, optionally the filter can be removed from the tray and washed by hand in a sink.

Optional higher grade filter materials are available, please contact us with your requirements!

Secure Mounting and Cable Routing

NEMA 1 rated wall mounted enclosure with conduit based cable entry/exit

Quickly install the WS-4345 by drilling two bolts to top keyed positions, placing the outer chassis onto the partially installed bolts and then installing the lower two bolts. Inner tray with HDD, Controller and PSU then easily mounts inside the exterior chassis.

Cable routing in and out of chassis can be installed through 1/2" conduit or secured via cable strain relief plugs.

Technical Specifications

Control Board
  • Addonics 5-Port HPM-XU Port Multiplier
  • Addonics.com for more information
  • (5x) Removable 3.5" Drive Trays
  • Support RAID 0/1/3/5/10, Clone Mode (N-Type) and JBOD
  • Hot-Swap support when using USB 3.0
External I/O
  • (1x) Power Status LED, Green
Internal I/O
  • (1x) USB 3.0 Type-B Port
  • Sliger recommends an Optical USB 3.0 Type B to Type A Cable for installs over 3 meters/10 feet
  • (1x) eSATA
  • (5x) Dip Switches for RAID configuration
  • Top-out exhaust cooling configuration for added dust resistance and thermal performance
  • (1x) 120mm PWM ball-bearing fan
  • (1x) 30 PPI Reticulated Polyurethane Air Filter
  • Filter can be removed from chassis and cleaned with water, or cleaned in place with vacuum or compressed air
Power supply
  • 150W FlexATX Form Factor Power Supply
  • Auto-on for HDD power
  • SECC — Steel, Electrogalvanized, Cold rolled, Coil, 16 and 18 Gauge
  • Black powdercoat door, unfinished steel chassis
  • Optional stocked or custom order colors
Dimensions (HxWxD)
  • 15-1/4" x 13" x 6"
  • 387.35mm x 330.20mm x 152.40mm
  • 20.45 lbs
  • 9.28 kg
  • FCC Class A Compliant
  • IP30 / NEMA 1
  • EN 62262 - IK08
  • 32°F to 158°F
  • 0ºC - 70ºC
  • 0% to 90% non-condensing

Documentation & Drivers



Description Ordering SKU
  • Wallmounting 5-Bay SATA DAS Enclosure
  • Includes Addonics 5-Port HPM-XU Board, 120mm Fan, 5 Drive Sleds, 150W PSU
  • Please specify required top conduit panel configuration on PO
  • WS-4345-A